Insta360 Invisible Dive case x4
Couldn't load pickup availability
- Complete invisible design, allowing for complete 360° shots underwater.
- Seamless underwater stitching.
- Waterproof to 164ft (50m).
- Crystal clear 360° video.
In the Box
Specs
How to Use
12y Anti-fon Inserts
1x 3-Prong to 1/4' Adapter
1x Dive Case Carry Pouch
1x Lens Cloth
Stability Pads
1s & Warranty & Guide Card
Dimensions
164 9 × 8/./ × 89.2mm 53.5 3.5In
maximum WED
1550 (5.50Z)
1. Open the case
Lift the buckle as shown below (©), then pull it down tc
remove.*rom he noxle) kenpa1 win the other 3 buckles
then open the Dive Case
Ensure that the anti-rog inserts are inserted as shown below
Note. When using third-party anti-log
size is within 371x19x1.2 mm. It the insert is too larde, it wi
cause water leakage and potentially damage the camera
3. Insert the Camer:
1) Before inserting the camera, you must activate Dive Case
Mode. Swipe down on the camera touchscreen to open (ne
shortcut menu, tap the Icon a or long press the 4 Dutton or IC
enter Dive Case Mode Once in Dive Case Mode, Dress the
Power Button to switch shooting modes and the Q Button to
start or stop shooting. For more into, refer to the Button
Instructons in lie las Mode below
2) Also, be sure that the camera lenses and the Dive Case
interior are clean and free of dirt or dust
3) When inserting the camera, be sure to remove any pre
installed lens guaros and take care
) scratch he lene
lose ine
loclosetheDrveCaselatchthebuckieontothecaseshook
and firmly push down until it clicks.
of the Dive Case in contact with its rubber seal are free of dirt
or dust
2) FO
r best results, keep the Dive Case lenses clean
b Omner accassonps
If vou are attaching the diving housing to other accessories.
such as the floating hand gnp, you can equip the screw
connection points with a stabilizing ring to secure tnt
darts will come loose or the camera will be damaged by
unratane
Invisible Selfie Stick and Dive Case in a straight line. Use the
wrench to tighten the 1/4 Thumb Screw to reduce the impact
or the water flow on the alignment
6. Stitching
For hest results when shooting underwater it's recommended
to keen the Dive Cases lenses perpendicular to the surface o
the water (so neither lens is facing upwards). After shooting
open the files in the Insta360 app or Studio and they will Dt
Noeyientecamet
Mode to ensure opumal image
qualitv. Swipe up on the
camera touchscreen or Iona press the button to exit Dive case mode
- Do not open the Dive Case while it is wet.
- After using the product in seawater, take out X4 and soak the Dive Case in fresh water for at least 10 minutes (ensure the Dive Case is firmly closed beforehand). If the Dive Case is not rinsed after use in seawater, residual salt may crystalize in gaps. These salt crystals will not dissolve in water and can lift the rubber seal and cause water leakage. After soaking the Dive Case in fresh water, rinse it under gently flowing tap water. Never apply a strong water stream from a single direction, as it may cause water leakage.
- Ensure that the dive case is firmly closed before washing. After washing, wipe away any water droplets remaining on the surface with a soft, dry cloth and leave to dry. Ensure there is no sand on the Dive Case before drying as sand may scratch the product surface when wiped with a cloth. Do not dry with a hair dryer or any other heat source.
- Do not store the Dive Case in a hot or humid environment. For example, do not leave it inside a hot car.
- Do not wash the Dive Case with soap, neutral detergent, or alcohol cleaning products. This may degrade the waterproofing performance.
- Store the product in a dry, well-ventilated location.